Wright Manufacturing Sentar Sport 26077 Spezifikationen

2007 Service Handbook“WHAT IT MEANS TO RIDE WRIGHT”

PFD Some parts have been revised but still are using same part #. ¾WS Upright Frame – Two styles, same part # 93420038 ¾52” Sentar Deck – Need ser

2007 Service Handbook Service Bulletins7

Hydro Hose Application Chart INFORMATION ONLY Subject: The following page is a chart to be used as a resource for determining the proper high pressure

High Pressure Hose Application ChartHydro hose part #Hose cut-lengthSentar1-S/Npriorto19729Sentar2-S/N19729andhigherSentar3-S/N26980andhigherSentarSpo

Bulletin # 055 6 Pages May 10, 2006 REMOVING HYDRAULIC OIL COOLER ON SPORT and RH MOWERS *** PRODUCT RECALL *** Subject: Removal of hydraulic oil cool

Bulletin # 055 6 Pages May 10, 2006 liability for consequential damage will be on the selling Dealer.This work is to be done in conjunction with Bulle

Bulletin # 055 6 Pages May 10, 2006 BHydraulic Oil Cooler Removal and Engine cooling area cleaning Instructions Sentar Sport and Rapid Height (RH) Sta

Bulletin # 055 6 Pages May 10, 2006 NOTE: The two photos below (Fig’s 3 & 4) are using the numbers 1 & 2 to indicate which hose from Fig 3 wil

Bulletin # 055 6 Pages May 10, 2006 Below is a copy of the letter being sent to each currently registered owner of the affected mowers. Keep in mind

Bulletin # 055 6 Pages May 10, 2006 Wright Warranty Quick-Claim-Form - Bulletins 055 and 056 only 1 mower per form Dealer Name: ______________________

Bulletin # 056 5 Pages May 10, 2006 ADDING MUFFLER HEAT SHIELD ON SPORT & RH MOWERS *** PRODUCT RECALL *** Subject: Adding the muffler heat shield

Bulletin # 056 5 Pages May 10, 2006 having knowledge of this recall due to non-registration, the liability for consequential damage will be on the sel

Bulletin # 056 5 Pages May 10, 2006 Installation Instructions for Replacement Heat Shield WMI part number: 91410026 Step One: Remove the four nuts on

Bulletin # 056 5 Pages May 10, 2006 Step Three: Install the replacement heat shield by directing the exhaust port mount under the muffler header brack

Bulletin # 056 5 Pages May 10, 2006 Below is a copy of the letter being sent to each currently registered owner of the affected mowers. Keep in mind

Bulletin # 057 1 Page May 10, 2006 Flat Rate GuideSubject: Moving to a Flat Rate system for determining allowed labor times. Also providing a parts c

301.360.9810 www.wrightmfg.com Fax 301.360.98204600X Wedgewood Blvd., Frederick, MD 21703FLAT RATE SCHEDULE INTRODUCTIONThis Flat Rate Manual is desi

FLAT RATE GUIDEWork Performed-R&RStander SentarVelkeMowerSport / RHNotesReturnPartsClutch0.8 1.2 0.8 0.8Sentar: may have to separate clutch or shi

Bulletin # 058 3 Pages June 29, 2006 Re-routing Z hydraulic hoseSubject: Re-routing hydraulic hose part number 33410075 UnitsAffected: All Mid-Mount Z

Bulletin # 058 3 Pages June 29, 2006 Bottom view of old routing configuration: Fig. 1 Hose routed horizontally below the hydro tank Top view of

Table of Contents Forms 1 Warranty Claim Form 2 Warranty Period Chart 3 Pre-Delivery Mower Service 4 Parts Order Issues (PFD) 6Se

Bulletin # 058 3 Pages June 29, 2006 Bottom view of new routing configuration: Fig. 3 26

Bulletin # 059 1 Page June 29, 2006 Sport / RH mower deck-lift update kitSubject: Providing a kit to repair malfunctioning deck lift systems• Part # 9

Bulletin # 060 1 Page August 29, 2006 Front caster part number information ** Information only ** Subject Providing part number information for front

Bulletin # 061 1 Page September 7, 2006 Cutting Deck Baffle-System Option Subject New optional deck baffle system UnitsAffected: All three bladed mach

Bulletin # 062 1 Page September 29, 2006 Sport & RH Deck Height Cog and Latch Kit Subject Updated deck height cog and latch kit KIT PART NUMBER:

Bulletin # 063 2 Pages October 5, 2006 PulleyParts information Subject The 71460069 pulley is being replaced with a new pulley UnitsAffected: Stander

Bulletin # 063 2 Pages October 5, 2006 This information applies to mower models that currently are using the 71460069 pulley1 Nut, 3/8 – 16 129900

2007 Service Handbook Service and Repair33

Neutral adjust on RTN models x Raise and secure machine x Using ¼” Allen, loosen (1) and move (2) up or down, until tire movement stops 12x Tighten

Wright ZTracking Adjustments¾Check and adjust tire pressure ¾Remove rear tires and loosen locking nuts at both pumps. (Fig 1) NOTE: If motor su

CHECKING AND ADJUSTINGDECK ALIGNMENT AND PITCH Alignment¾Check and adjust tire pressure ¾Set deck to 3” ¾Measure top of deck to floor.a) Trim side

FrontWright Z ¾Deck alignment and pitch adjustments NOTES:___________________________________________________________________________________________

Sentar¾ Deck alignment and pitch adjustments 16 ½”FrontRearRaise or lowerone side Pitch adjustments38

WSES, WSR ¾Alignment and pitch are somewhat limited. NOTES:__________________________________________________________________________________________

Deck Height Adjustments WSSBlade Adjustments and Height-of-Cut Before Adjusting the Height-of-Cut be sure of proper air pressure in all four tires and

 Use the lowest holes in tractor frame for cutting heights of 3.25" - 4.5"..NOTES:________________________________________________________

Deck Height AdjustmentsWS, WV Hydro 2.5-3.75”3.25-4.5”1.75-3.0”3”42

Deck Height AdjustmentsVelke Gear/Belt Drive NOTES:___________________________________________________________________________________________________

Cutting Deck Baffle System Installation Instructions 1. Remove deck covers. 2. Raise and secure unit so cutter deck is accessible. 3. Mount baffle a

Baffle installation with-out pre-punchedholes in cutter deck 1. Remove deck covers. 2. Raise and secure unit so cutter deck is accessible. 3. Remove b

2007 Service Handbook Forms1

Engine Does Not CrankProblem Possible Causes or SolutionBattery Voltage Below 12 Volts Follow Charging System Troubleshooting GuideParking Brake Not S

REQUIREMENTSFor A Successful Clutch Installation Two Critical Requirements: 1. Anti-rotation device must allow both axial and radial free-play!Failure

Clutch Evaluation Measuring Coil Resistance: ¾Turn engine and PTO off. ¾Disconnect clutch at connector. ¾Select meter settings for ohm reading. ¾C

Problem Possible CausesSolutionLow coil resistance Replace with new Magstop unitDefective battery Replace Faulty charging system Repair or replaceBad

301.360.9810 www.wrightmfg.com Fax 301.360.98204600X Wedgewood Blvd., Frederick, MD 21703This tool is to assist in compressing the idler arm tension

Hydro PumpExternal Maintenance ¾Check fluid level in reservoir ¾Level should be 1”-1 ½” below the top of the oil fill ¾Inspect drive belt, idler pu

Possible Cause Corrective ActionVehicle tires improperly inflated Set to suggested pressureControl linkage bent, loose or out of adjustment Repair, ad

Sentar Sport and Stander RH Deck-Lift System ImprovementKit-95460005 and 95460006 Removal of Original Lift System 1. Deck Lift Spring Removal:

5. Disconnect Castor Frame and Frame Rail:a. Remove the four bolts and nuts connecting the right half of the front castor frame to the mower

8. Remove Front Engine Deck Pins:a. Using ½” socket and wrench remove bolts and nuts (Fig. 8, A) and use a punch to remove pins. (Fig. 8, B)9. Se

InstructionsModel Number: ______________Serial Number: ______________Hour Meter Reading:___________Copies to: White - Wright Mfg. Inc. z Yellow - Dist

11. Removing the Rear Lift-Axle Pins:a. Remove both rear lift axle pins (Fig. 10, A); ensure deck weight is resting on 2X4’s. b. Pry or punch pi

2. Install Lift Bar Linkage: a. Install lift bar linkage and attach with e-clip. (Fig. 12)3. Reinstall Lift Handle. 4. Slide Unit Together. 5. Reattac

7. Install Front Lift Axle: a. Place Stainless steel shaft into front deck lift axle (Fig. 14). The tab end of shaft goes on the operator’s side

8. 95460006 KIT ONLY a. Install bronze bushings into the journals in the front frame as shown in Fig. 18.9.Reconnect Castor Frame to Frame Rail (Fig.

11. Install Connector Arm to the Groove Pin on the Front Lift Axle, Install E-Clip: NOTE: Use deck lift handle to align. (Fig. 21) 12. Raise Jack an

Deck-Lift Parts Diagram REF # DESCRIPTION PART # REF # DESCRIPTION PART # 1 1/2" LOW PROFILE NUT (4) 12990018 12 FRONT S.S. AXLE (1)

4600X Wedgewood Blvd Frederick, MD 21703www.wrightmfg.com

Warranty Period Changes4/01/05 Retail sale and later3/17/03 Retail sale and later3/01/02 Retail sale and laterAll previousGeneral2 year P&L 1P&

PRE-DELIVERY SERVICE OF MOWER BY DEALER The Wright Mower is shipped completely assembled and has been adjusted and tested at the factory. However, due

if the parking brake locking system (if applicable) prevents the unit from being driven while engaged. If not, service the parking brake locking syste